Welcome toA clothing company

Anti-rust Oil Flow Meter: Anti-rust Oil Monitoring Solution for Hot-Formed Parts Shot Blasting and Oil Coating Line

Project Background

The shot blasting and oil coating line for hot-formed automotive parts is an important part of the production process for automotive parts (mainly A-pillars and B-pillars). After shot blasting, the surfaces of the parts need to be coated with anti-rust oil to prevent rusting during subsequent storage and transportation. Whether the application amount of anti-rust oil is normal and consistent directly affects the anti-rust performance of the parts and the subsequent assembly quality.

This customer is the leading manufacturer of oil coating line equipment in the industry in terms of shipment volume. Previously, the front end of its equipment used a pressure tank for liquid supply, while the back end used a Keyence ultrasonic flow meter. A gear flow meter was also tried. However, in actual use, since the anti-rust oil can be recycled and may contain oxide layer impurities, and has a relatively high viscosity (45–100 cP), the original flow meter's filter screen was prone to clogging, requiring frequent filter screen replacements, resulting in high maintenance costs and frequent downtime. Later, the equipment was modified to have ten branch lines, controlled by valves, which placed higher demands on the stability and anti-clogging capabilities of the flowmeters.

Based on the customer's operating conditions, the Cixi technical team recommended the use of the CX-PZ-10 nozzle flow meter, which effectively solved the problems of filter clogging and frequent maintenance. Currently, each set of equipment is equipped with one unit to stably monitor whether the anti-rust oil is being dispensed normally.

Challenges Faced

Filter prone to clogging

Anti-rust oil can be recycled and may contain oxide layer impurities. The original gear flow meter filter is prone to clogging and needs to be replaced frequently.

High-viscosity medium

The viscosity of the anti-rust oil is 45-100 cP, which is a medium-to-high viscosity fluid. This places high demands on the compatibility and measurement stability of the flow meter.

Multi-branch regulation

Subsequently, the equipment was fitted with ten branch lines, which were regulated by valves. The flow meter needed to operate stably in each branch line and not be affected by pressure fluctuations.

Oil Discharge Status Monitoring

The core requirement is to monitor whether the oil discharge is normal, rather than high-precision measurement. This requires the flow meter to be stable and reliable, with simple maintenance.

Operating Condition Analysis

Key operating parameters

  • Medium: Anti-rust oil (recyclable, may contain oxide layer impurities)

  • Flow rate: 100 ml/min

  • Pressure: Approximately 3-5 kg

  • Viscosity: Approximately 45-100 cP

  • Front-end power source: Currently a pressure tank (can be replaced with a pump)

  • Application equipment: Shot blasting and oil coating line for automotive hot-formed parts

  • Application scenario: A part of the production process for automotive A-pillars and B-pillars

Core function:Monitor whether the oil is being dispensed normally to ensure that the oiling process is stable and reliable.

ffbbPzjcY.jpg

Industry Analysis

First
Customer Industry Shipment Ranking
1 unit/set
Single equipment configuration
10 units
Number of branch lines (valve control)
100ml/min
Typical flow rate

This customer is a leading company in the industry of shot blasting and oil coating line equipment for hot-formed parts, ranking first in shipment volume. Previously, the use of Keyence ultrasonic flowmeters was costly, and gear flowmeters experienced frequent filter clogging and maintenance due to impurities in the anti-rust oil. The CX-PZ-10 nozzle flow meter, with its anti-clogging, high-viscosity resistance, and stable and reliable characteristics, successfully replaced the original solution and became the standard configuration for the customer's oiling line.

Solution

Based on the operating conditions and pain points of the shot blasting and oil coating line, the Cixi technical team recommended the use of the CX-PZ-10 nozzle flow meter and developed a targeted replacement and upgrade solution.

1

Model Selection and Replacement

For a flow rate of 100 ml/min, a viscosity of 45–100 cP, and anti-rust oil containing impurities, the CX-PZ-10 nozzle flow meter was selected to replace the original Keyence ultrasonic flow meter.

2

Anti-clogging design

The nozzle flow meter structure does not have a filter, effectively preventing clogging issues caused by oxide layer impurities and significantly reducing maintenance frequency.

3

Multi-branch adaptation

Suitable for operating conditions with ten branches and valve regulation, providing stable monitoring of the anti-rust oil discharge status in each branch.

4

Oil discharge status monitoring

Real-time monitoring of whether the oil is being dispensed normally, meeting the core needs of customers, stable and reliable, and easy to maintain.

Implementation Results

This solution has been applied in large quantities on the customer's hot-formed parts shot blasting and oil coating line. Each set of equipment is equipped with one CX-PZ-10 nozzle flow meter, which effectively solves the problems of filter clogging and frequent maintenance associated with the original ultrasonic flowmeters.

Filter clogging issuesComplete resolution
Maintenance frequencySignificantly reduced
Oil discharge status monitoringReal-time and reliable
Multi-branch adaptabilityStable operation

Customer Reviews

Previously, we used Keyence's ultrasonic flow meters, which were expensive. The filters of the gear flow meters kept clogging, and replacing the filters was a headache. Later, we set up ten branch lines with valves for regulation, but it still didn't work well. After switching to Cixi's nozzle flow meter, the clogging problem was completely resolved. Oil discharge monitoring is very stable, and maintenance is hassle-free. We are the industry leader in terms of shipment volume, and we are very careful in selecting our suppliers. We are very satisfied with CIXI's solution.

W
Mr. Wang                                General Manager · Hot Forming Oiling Line Equipment Manufacturer

Get a Customized Solution

Our engineers will contact you within 24 hours with professional product selection advice and technical support