Welcome toA clothing company

What should be considered when selecting an explosion-proof flow meter? How do you choose the explosion-proof rating?

2026-09-18 11:18:57
views
Reading time: about 5 minutes

Q:What should be considered when selecting an explosion-proof flow meter? How do I choose the explosion-proof rating?

A:The core logic for selecting an explosion-proof flow meter isFirst, match the hazardous area, then determine the explosion-proof type, and finally verify the certification and accessories.Step 1: Determine the explosion-proof type based on the hazardous area classification of the site (Zone 0, Zone 1, Zone 2) – Zone 0 must use the intrinsically safe type (Ex ia), while Zone 1/Zone 2 can use either the flameproof type (Ex d) or the intrinsically safe type (Ex ib). Step 2: Interpret thegas group(IIC covers the most hazardous gases such as hydrogen and acetylene) andTemperature Group(T6 surface temperature ≤85°C, highest safety level) Step 3: Verify the explosion-proof certificate and its validity period, and confirm that the explosion-proof marking matches the site area. Intrinsically safe flow meters must also be equipped with safety barriers certified by an explosion-proof inspection agency to constitute an intrinsically safe explosion-proof system. GN Instruments can provide explosion-proof gear flowmeters, explosion-proof gas mass flowmeters/controllers, explosion-proof vacuum gauges, and other products, covering both intrinsically safe and flameproof solutions.

I. How to choose the explosion-proof type? First, consider the hazardous area

The explosion-proof type determines the scope of use of the flow meter in hazardous areas. The two most common types areIntrinsically Safe (Ex ia/ib)andFlameproof (Ex d)When selecting a model, the first step is to determine the model based on the hazardous area classification of the site.

Hazardous AreaRecommended Explosion-Proof TypePrincipleApplicable Scenarios
Zone 0 (Continuous presence of explosive gases)Intrinsically Safe Ex iaLimits circuit energy so that even a fault will not generate an ignition sourceInside sealed containers, extremely hazardous areas where gases are continuously present
Zone 1 (may occur occasionally during normal operation)Flameproof Ex d or intrinsically safe Ex ibEx d withstands internal explosions without propagation; Ex ib limits energyAround chemical reactors, pump rooms, and compressor areas
Zone 2 (unlikely to occur during normal operation)Flameproof Ex d, intrinsically safe Ex ib, increased safety Ex eVarious explosion-proof types can be accommodatedGeneral chemical workshops, periphery of storage tank areas

Key Decision: Intrinsic Safety vs. Explosion-Proof

  • Intrinsically Safe (Ex ia):The energy in the circuit is limited,No ignition source will be generated.Small size, light weight, suitable for low-power instruments (sensors, flow meter signal loops). Can be used in Zones 0, 1, and 2. However, it must be used in conjunction withsafety barrierThe safety barrier is installed in the safe area.

  • Flameproof (Ex d):The enclosure can withstand internal explosion pressure,Even if an internal explosion occurs, it will not propagate to the outside.. Suitable for high-power electrical loads, no safety barrier required, butIt cannot be used in Zone 0,and the enclosure must not be opened while energized on site.

  • Composite Type (Ex db ib):Some explosion-proof flowmeters adopt a hybrid design consisting of an explosion-proof meter head and an intrinsically safe sensor electrode, balancing safety with signal accuracy, and are suitable for Zones 1/2.

II. Three Elements of Explosion-Proof Markings: Zone, Gas Group, Temperature Group

Each parameter in the explosion-proof marking (e.g., "Ex ia IIC T6 Ga") must match the on-site operating conditions, and none of them can be omitted.

Equipment Protection Level (Ga/Gb/Gc)
Ga corresponds to Zone 0 (highest), Gb to Zone 1, and Gc to Zone 2. When selecting a model, the EPL level must match≥meet the site area requirements.
Gas Group (IIA/IIB/IIC)
IIA is the mildest (propane), IIB is moderate (ethylene),IIC is the most hazardous (hydrogen, acetylene)The IIC rating can cover IIA/IIB environments.
Temperature Groups (T1~T6)
T6 surface temperature ≤85°C (safest), T1 ≤450°C (for gases with the highest ignition temperature). The higher the temperature group, the lower the allowable temperature on the equipment surface, and the greater the safety margin.
Temperature GroupMaximum surface temperature of the equipmentTypical applicable gases
T1≤450℃Hydrogen, acrylonitrile, etc. (gases with high ignition temperatures)
T4≤135℃Most industrial gases (acetaldehyde, diethyl ether, etc.)
T6≤85℃Ethyl nitrate, ethyl nitrite (gases with the lowest ignition temperatures)

III. Considerations for Selecting an Explosion-Proof Flow Meter

PrecautionsDescription
Verification of Explosion-Proof CertificateThe supplier must be required to provide a valid explosion-proof certificate, verify the certification body (NEPSI, ATEX, IECEx), the explosion-proof marking and its validity period, and confirm that it matches the site area.
The intrinsically safe type must be equipped with a safety barrier.Intrinsically safe flowmeters cannot be used alone. They must be connected to a safety barrier certified by an explosion-proof inspection agency to form an intrinsically safe explosion-proof system. The safety barrier is installed in the safe area.
Cable and Wiring RequirementsThe intrinsically safe circuit must use a shielded cable, with the shield grounded at one end in the safe area. The cable parameters (capacitance, inductance) must meet the intrinsic safety parameter requirements of the safety barrier and the flow meter.
Reliable groundingThe flow meter housing must be reliably grounded, and the explosion-proof grounding wire must not be shared with the protective grounding of the high-voltage system. If there are no grounding conditions, the manufacturer should be informed.
Flameproof type: Do not open the cover while powered.Flameproof flowmeters are not permitted to have their housings opened on-site while energized for circuit adjustments. It is recommended to prioritize the selection of intrinsically safe or infrared touch button models, which allow parameter settings to be completed without opening the cover.
Matching of medium temperature and explosion-proof ratingThe surface temperature of the flow meter must not exceed the limit of the indicated temperature group. For high-temperature media, an explosion-proof flow meter with a cooling structure or a high-temperature type should be selected, and the surface temperature should be calculated.

IV. Explosion-proof solutions for common flow meter types

flow meter TypeTypical explosion-proof markingsApplicable Area
Oval Gear flow meterIntrinsically Safe Ex ia IIC T4; Explosion-Proof Ex d IIB T4Zone 1/Zone 2 (intrinsically safe up to Zone 0)
Gas Mass Flow Meter/ControllerIntrinsically Safe Ex ia IIC T6 Ga (Zone 0); Increased Safety Ex eb IIC T4 (Zone 1)Zone 0/Zone 1/Zone 2 (depending on configuration)
Electromagnetic flow meterFlameproof and intrinsically safe Ex db ib IIC T6 GbZone 1/Zone 2
Vortex flow meterIntrinsically Safe Ex ia IIC T6; Explosion-Proof Ex d IIC T6Zone 1/Zone 2

V. GN Instruments Explosion-Proof flow meter Solution

For potentially explosive environments,GN Instruments Instrument Co., Ltd.can provide the following explosion-proof product solutions:

Product SeriesExplosion-proof typeExplosion-proof Rating ReferenceApplicable Scenarios
Explosion-proof gear flow meterIntrinsically Safe / Explosion-ProofEx ia IIC T4 / Ex d IIB T4Measurement of flammable liquids in the chemical and petroleum industries, and settlement of oil product trades
Explosion-proof gas mass flow meter/controllerIntrinsically Safe / Increased SafetyEx ia IIC T6 Ga / Ex eb IIC T4Measurement and control of flammable gas flow, chemical and semiconductor process gases
Explosion-proof vacuum gaugeIntrinsically SafeEx ia IIC T4Vacuum monitoring in flammable and explosive environments

Based on your hazardous area classification, gas type, temperature group, and flow conditions, our engineers will recommend suitable explosion-proof types and product models, and confirm the requirements for safety barriers, cables, grounding, and other related components. If necessary, explosion-proof certificate verification and prototype testing services can be provided.