Q:How should I select a gear metering pump for high-temperature operating conditions? What issues should be considered?
A:High-temperature operating conditions impose far more stringent requirements on gear metering pumps than those at normal temperatures. Ordinary gear pumps may experience the following issues under high-temperature conditions:material softening, thermal expansion seizure, seal failure, and reduced lubrication performanceand other issues, so selection cannot simply be based on normal temperature conditions. The selection of high-temperature gear metering pumps needs to be considered systematically based ontemperature range and speed limits, material temperature resistance, thermal expansion clearance design, sealing solutions, cooling/insulation methods, and drive configurations.six core dimensions. GN Instruments offers the CXG series of high-temperature gear metering pumps, which can operate at temperatures up to 330°C and be cleaned at temperatures up to 450°C. They are suitable for the transfer and metering of high-viscosity, high-temperature media such as high-temperature resins, hot-melt adhesives, asphalt, and polyurethane.
| Challenge | Detailed Description | Consequences of improper model selection |
|---|---|---|
| Thermal expansion causes changes in clearance | Metal components expand at high temperatures, reducing the clearance between the gears and the pump body, which may lead to seizing or increased wear. | Pump body seizure, gear wear, loss of metering accuracy |
| Decreased material strength | The hardness, wear resistance, and fatigue resistance of conventional materials decrease at high temperatures. | Accelerated gear wear, significantly shortened pump life |
| Seal failure | Conventional rubber seals age, carbonize, and lose elasticity at high temperatures | Medium leakage, environmental pollution, and even safety incidents |
| Decreased lubrication performance | At high temperatures, the viscosity of the medium decreases, the lubrication film becomes thinner, and bearing wear accelerates. | Bearing life drops sharply, vibration and noise increase, and the pump body is damaged |
| Temperature Range | Recommended Solution | Key Points to Note |
|---|---|---|
| ≤ 200℃ | Stainless steel pump body (304/316L), high-temperature resistant seal | If the medium temperature exceeds 90°C, it must be specifically indicated during model selection to ensure seal compatibility. |
| 200~330℃ | High-temperature special type, chromium-nickel alloy steel or high-temperature tool steel | Requires a thermal expansion gap design, preheating before startup, and rotational speed control within 30-50 rpm |
| 330–450°C (including cleaning) | CPM tool steel or titanium-tantalum alloy material, special seal | Requires specialized high-temperature design, equipped with a cooling system to protect the bearings and seals [reference:10] |
The following information must be confirmed before selection:
Medium name and temperature:Specific medium name, maximum operating temperature, cleaning temperature, and temperature fluctuation range.
Medium properties:Viscosity (at operating temperature), corrosivity, solids content, and whether it is prone to crystallization or vaporization.
Flow rate range:Minimum flow rate, normal flow rate, maximum flow rate, and required metering accuracy.
Pressure rating:Inlet pressure, outlet pressure, system pressure differential; the pressure rating may need to be derated at high temperatures.
Sealing requirements:Whether a metal bellows seal is required, and whether a sealed cooling jacket or insulation jacket is required.
Cooling/insulation method:Whether pump body jacket heating or cooling is required, and the type of heating medium.
Drive method:Whether variable frequency speed control is required, whether an explosion-proof motor is required, and speed control requirements.
Installation conditions:Installation orientation, piping connection method, available space.
| Common misconceptions | Typical manifestations | Possible consequences |
|---|---|---|
| Ignoring thermal expansion clearance | Selection based on room-temperature clearance, without accounting for high-temperature expansion allowance | Gear seizure or excessive clearance-induced leakage at high temperatures prevents the pump from operating normally. |
| Improper selection of seals | Standard nitrile rubber seals are still used in high-temperature environments. | The seal fails within 200 hours, causing medium leakage and environmental pollution. |
| No preheating before startup | Direct start-up in a cold state, medium condensation causes the start-up torque to exceed the standard | Pump body seizure, gear breakage; 90% of seizure cases originate from this cause. |
| Excessive rotational speed | High-temperature operating conditions still run at normal speed | Increased gear wear, with service life dropping sharply from 8,000 hours to 500 hours |
For high-temperature operating conditions,GN Instruments Instrument Co., Ltd.can provide the CXG series of high-temperature gear metering pumps. The main parameters are as follows:
| Product Series | Operating Temperature | Cleaning temperature | Key Features |
|---|---|---|---|
| CXG Series High-Temperature Gear Metering Pump | Up to 330°C | Up to 450°C | The pump body is drilled with heating holes, and the speed ratio of the reducer is increased under high-temperature conditions, allowing for controllable rotational speed. |
| High-temperature melt pump | Up to 510°C | Up to 590°C | CPM tool steel or titanium-tantalum alloy, with an outlet pressure of up to 70 MPa |
The CXG series high-temperature gear metering pump features a double circular arc sinusoidal tooth profile, where the tooth profile surfaces do not experience relative sliding during engagement, resulting in smooth operation, low noise, and a long service life. Depending on the properties of the medium, a combination of sealing methods such as a fluororubber skeleton oil seal, a graphite packing seal, or a PTFE packing seal can be selected [reference:18]. The drive can be equipped with an optional servo motor, stepper motor, explosion-proof motor, or brushless motor to meet the requirements of different sites.
Based on your fluid name, maximum operating temperature, viscosity, flow rate range, pressure, and sealing requirements, our engineers will recommend a suitable CXG series high-temperature gear metering pump model and configuration solution. For extreme high-temperature conditions exceeding 330°C, a high-temperature melt pump solution can be recommended. If necessary, we can provide prototype testing services to verify metering accuracy and long-term stability under actual high-temperature operating conditions.