Q:How exactly can very low flow rates be measured accurately in a laboratory or on a production line?
A:First, confirm the medium, minimum/maximum flow rate, viscosity, temperature, pressure, corrosivity, allowable pressure drop, and accuracy. For liquids in the mL/min range, evaluate micro-gear flowmeters or micro-Coriolis mass flowmeters; for gases, evaluate thermal mass flowmeters/MFCs. When direct mass flow measurement is required, prioritize the evaluation of Coriolis flowmeters. During installation, pay attention to filtering, venting, pressure stabilization, and pulsation suppression, and calibrate according to the actual medium.
Weak signal, low signal-to-noise ratio:The smaller the flow rate, the weaker the sensor's raw signal, which is easily overwhelmed by electrical noise and zero drift, placing extremely high demands on the circuitry and algorithms.
The impact of temperature is amplified:The liquid viscosity changes exponentially with temperature, and the gas volume changes with temperature and pressure, both of which directly affect the readings.
Bubble and pulsation interference:A single bubble in a micro-channel can cause significant deviations; flow pulsations in plunger pumps and gear pumps can also interfere with instantaneous values.
Mostly in a laminar flow state:At low flow rates, medium flow is mostly laminar, and the relationship between flow rate and signal is often nonlinear, requiring calibration for each individual unit.
Risk of clogging and internal leakage:The internal clearance of positive displacement meters is extremely small, and tiny particles can cause jamming, and wear can lead to internal leakage.
The first step in model selection is to determine the properties of the medium: whether it is a liquid or a gas, its viscosity level, whether it is conductive, and whether it contains particles. Then, the corresponding measurement principle is matched.
| Measurement Principle | Typical Instruments | Applicable Flow Range | Accuracy Level | Applicable Scenarios |
|---|---|---|---|---|
| Positive displacement | miniature gear flow meter / Oval Gear flow meter | 0.5 mL/min ~ tens of L/min | ±0.5% of reading | Metering of high-viscosity liquids, lubricating oils, resins, adhesives, and chemical solutions |
| Direct mass (Coriolis force) | Coriolis mass flow meter | Several g/h ~ Several tens of kg/h | ±0.1% ~ ±0.2% | Large changes in density/temperature, mixed media, fine chemical formulation control |
| Thermal diffusion | Thermal Gas Mass Flow Meter/Controller (MFC) | 0.1 sccm ~ tens of slpm | ±1% F.S. | Micro gas flow, carrier gas, gas distribution, semiconductor processes |
| Electromagnetic induction | Miniature electromagnetic flow meter | Several mL/min ~ L/min | ±0.5% | Conductive liquids, no flow restrictors, slurries containing particles |
| Differential Pressure / Laminar Flow | Laminar Flow Meter | μL/min ~ mL/min | ±1% | Gas calibration, leak detection, microflow research |
One-sentence selection logic:
Liquid + High Viscosity →Micro Gear/Oval Gear flow meter
Liquid + large changes in density or temperature →Coriolis mass flow meter
Gas + Very Low Flow Rate →Thermal Mass flow meter / MFC
Conductive liquid + particles →Miniature Electromagnetic flow meter
Range matching, with the operating point falling between 20% and 80%:Do not use a large flow meter to measure small flow rates. When the actual flow rate is 10 mL/min, select a meter with a range of 0–20 mL/min. The accuracy is usually one order of magnitude higher than that of similar products with a range of 0–200 mL/min.
Temperature control and compensation:For high-viscosity media, it is recommended to use constant-temperature delivery, or to select a flow meter with temperature compensation and a temperature-controlled jacket to keep viscosity fluctuations within the range allowed by the process.
Exhaust and pulsation damping:An air vent valve is installed at the highest point of the pipeline, and a pulsation dampener is installed at the pump outlet to ensure that the pipeline is fully filled with the medium, free of air bubbles, and free of severe pulsations.
Filtration and Back Pressure:Install a 5–20 μm filter upstream of the positive displacement meter and maintain a back pressure of 0.05–0.2 MPa to prevent cavitation and internal leakage.
Correct installation:Ensure there is a sufficient length of straight pipe section and avoid installation in the negative pressure zone at the pump inlet. For vertical pipes, it is recommended to have flow from bottom to top to ensure the pipe is always full.
Actual liquid calibration and periodic calibration:It is recommended that low-flow meters be calibrated according to the actual medium; after commissioning, they should be re-inspected once a year, and the calibration interval should be shortened for applications involving trade settlement or formula control.
Micro-injection of lubricating oil/hydraulic oil (1–100 mL/min):The M series micro-gear flow meter is preferred. Its positive displacement principle is not affected by viscosity, and it is recommended to use it with a pulse damper.
Resins, adhesives, high-viscosity colloids (0.5~50 mL/min):Select an oval gear flow meter or a miniature gear flow meter, paying attention to heating and insulation as well as material compatibility.
Fine chemical formulations, media with fluctuating density:Use a miniature Coriolis mass flow meter to directly measure mass flow without the need for density conversion.
Semiconductor/analytical instrument carrier gas (sccm level):A thermal mass flow controller (MFC) with temperature compensation and closed-loop control is used.
Conductive chemical solutions, slurries containing particles:A miniature electromagnetic flow meter is used, which has no flow restrictors, low pressure loss, and is not prone to clogging.
GN Instruments Instrument Co., Ltd.Focused on precision flow measurement and control, we can provide the following for low-flow applications:
M Series Micro Gear Flow Meters:The minimum measurable flow rate is as low as 0.5 mL/min, with an accuracy of ±0.5% of the reading. Gears and bearings made of materials such as 316L, Hastelloy, and PEEK are available, making them suitable for various high-viscosity media.
Miniature Coriolis mass flow meter:Directly measures mass flow, unaffected by changes in temperature, pressure, and density, making it suitable for formulation control in fine chemicals and biopharmaceuticals.
Thermal Mass flow meter/Controller:Covers sccm-level micro-gas flows and supports both analog and digital communication outputs.
Supporting Services:We provide operating condition calculations, prototype testing, and actual liquid calibration, as well as one-on-one model selection support from our engineers.
Model Selection Recommendations:Please provide operating parameters such as the name of the medium, operating viscosity, flow rate range (normal value/minimum value), temperature, pressure, accuracy requirements, and pipeline material. Our engineers will recommend a suitable model for you.